Chemical

  


Pre-press Chemistry

Fujifilm has developed an extensive range of processing chemistry for both plate and film products, along with a range of plate care products. All are designed to complement Fujifilm film and plate products and processing equipment.

****

Plate Processing


Plate Care



Processor Care


Film Processing

****


Plate Processing

DT-2RE Replenisher

Replenisher for use with DT-2WE Developer


HD LH-PJE

DT-2WE Developer

FN-6CWE Gum

Replenisher for use with DT-2WE Developer when used with Brillia HD LH-PJE plates in Fuji FLH-Z & P range of Fuji plate processors.


Aqueous based developer
DT-2RE Replenisher is a water based chemical with good environmental properties. This results in easier chemical disposal.

Low replenishment rates
Lower replenishment volumes means less chemical waste and therefore lower waste management costs.

Activity controllable
DT-2RE Replenisher in combination with DT-2WE developer will allow the developer activity level to be judged by conductivity allowing instant assessment of the developer condition preventing poor development, press downtime and additional costs.

DT-2RWE Replenisher

Replenisher for use with DT-2WE Developer


HD LH-PJE

DT-2WE Developer

FN-6CWE Gum

Replenisher for use with DT-2WE Developer when used with Brillia HD LH-PJE plates in Fuji FLH-E/E2 and non-Fuji plate processors.


Aqueous based developer
DT-2RE Developer Replenisher is a water based chemical with good environmental properties. This results in easier chemical disposal.

Low replenishment rates
Lower replenishment volumes means less chemical waste and therefore lower waste management costs.

Activity controllable
DT-2RWE Replenisher in combination with DT-2WE Developer will allow the developer activity level to be judged by conductivity allowing instant assessment of the developer condition preventing poor development, press downtime and additional costs.

Ready to Use
DT-2RWE replenisher is a ready to Use replenisher which can be used direct from the bottle without additional mixing.

DT-2WE Developer

An adaptable Developer for Brillia HD LH-PJE plate


HD LH-PJE

DT-2RE Replenisher

DT-2RWE Replenisher

FN-6CWE Gum

An adaptable Developer for Brillia HD LH-PJE plate allowing processing in a variety of plate processing equipment.


Economical usage
DT-2WE Developer has very good chemical yield properties. This results in good cost savings achieved from long developer life, stable processing conditions and low replenisher amount requirements.

Reduced maintenance times
DT-2WE Developer is a very clean working developer. Less time is required to clean the developer tank within the processor during the periodical processor maintenance cycle.

Easy to use
DT-2WE Developer comes in Ready-to-Use bottles, eliminating the need for mixing and reducing the possibility for error.

Aqueous based developer
DT-2WE Developer is a water based chemical with good environmental properties. This results in easier chemical disposal.

"Open" processing
DT-2WE Developer allows LH-PJE plates to process through a variety of plate processing equipment creating an open system. This gives greater options and flexibility in the processing stage.

FCT-E12 Developer

An adaptable Developer for Brillia HD LH-PJE and LH-PIE plates


HD LH-PJE

FCT-E13 Replenisher

FN-6CWE Gum

An adaptable developer for Brillia HD LH-PJE and LH-PIE plates allowing plate processing in a variety of plate processing equipment.


Economical usage
FCT-E12 Developer has very good chemical yield properties. This results in good cost savings achieved from long developer life, stable processing conditions and low replenisher amount requirements.

Reduced maintenance times
FCT-E12 Developer is a very clean working developer. Less time is required to clean the developer tank within the processor during the periodical processor maintenance cycle.

Easy to use

FCT-E12 Developer comes in Ready-to-Use bottles, eliminating the need for mixing and reducing the possibility for error.

Aqueous based developer
FCT-E12 Developer is a water based chemical with good environmental properties. This results in easier chemical disposal.

"Open" processing
FCT-E12 developer allows LH-PJE and LH-PIE plates to process through a variety of plate processing equipment creating an open system. This gives greater options and flexibility in the processing stage.

FCT-E13 Replenisher

Replenisher for use with FCT-E12 Developer


HD LH-PJE

FCT-E12 Developer

FN-6CWE Gum

Replenisher for use with FCT-E12 Developer when used with Brillia HD LH-PJE and LH-PIE plates.


Low replenishment rates
Lower replenishment volumes means less chemical waste and therefore lower waste management costs.

Aqueous based developer
FCT-E13 Developer Replenisher is a water based chemical with good environmental properties. This results in easier chemical disposal.

Easy to use
FCT-E13 Replenisher comes in Ready-to-Use bottles, eliminating the need for mixing and reducing the possibility for error.

HD-N1 Developer & Replenisher

Negative working PS-Plate Developer


FND-E

Negative Working PS-Plate Developer for use with all Fujifilm negative working plates (except VNN-E).


Aqueous based developer
HD-N1 Developer and Replenisher is a water based chemical with good environmental properties. This results in easier chemical disposal.

HD-N2 Developer & Replenisher

Negative working PS-Plate developer


Negative Working PS-Plate Developer for use with VNN-E Newspaper plate


Specifically designed
A developer designed for the harsh environment encountered in Newspaper production

Cost savings
Used in combination with VNN-E plates results in low replenishment rates and high developer yield giving longer periods between processor maintenance.

HD-P2 DW Developer

Positive working PS-Plate Developer


VPS-E

VPU

HD-P2 RW Replenisher

Positive Working PS-Plate Developer for use with all machine processed Fujifilm Positive working plates.


Aqueous based developer
HD-P2 developer is a water based chemical with good environmental properties.

Economical usage
HD-P2 developer has very good chemical yield properties. This results in good cost savings achieved from long developer life, stable processing conditions and low replenisher amount requirements.

Reduced maintenance times
HD-P2 developer is a very clean working developer. Less time is required to clean the developer tank within the processor during the periodical processor maintenance cycle.

HD-P2 RW Replenisher

Positive working PS-Plate Replenisher


VPS-E

VPU

HD-P2 DW Developer

Positive Working PS-Plate Developer Replenisher for use with all machine processed Fujifilm Positive working plates.


Aqueous based Developer Replenisher
HD-P2 Developer Replenisher is a water based chemical with good environmental properties. This results in easier chemical disposal.

Easy to use
HD-P2 Developer Replenisher comes in Ready-to-Use bottles, eliminating the need for mixing and reducing the possibility for error.

HD-P7 Developer & Replenisher

A flexible developer for Brillia LH-PCE plates


LH-PCE

FN-6CWE Gum

An adaptable developer for Brillia LH-PCE allows processing in a variety of plate processing equipment.


Aqueous based developer
HD-P7 Developer is a water based chemical with good environmental properties. This results in easier chemical disposal.

Economical usage
HD-P7 developer has very good chemical yield properties. This results in good cost savings achieved from long developer life, stable processing conditions and low replenisher amount requirements.

Reduced maintenance times
HD-P7 developer is a very clean working developer. Less time is required to clean the developer tank within the processor during the periodical processor maintenance cycle.

Easy to use
HD-P7 Developer comes in Ready-to-Use bottles, eliminating the need for mixing and reducing the possibility for error.

Open processing
HD-P7 developer allows LH-PCE plates to process through a variety of plate processing equipment creating an open system. This gives greater options and flexibility in the processing stage.

LH-DPRE Replenisher

Replenisher for use with Brillia LH-PIE plate


LH-DPWE Developer

FN-6CWE Gum

LH-DPRE Developer Replenisher is designed for use with Brillia LH-PIE positive thermal plates.


Aqueous based developer
LH-DPRE Developer Replenisher is a water based chemical with good environmental properties. This results in easier chemical disposal.

Low replenishment rates
LH-DPRE features a very low replenishment rate creating less chemical waste and therefore lower waste management and usage costs.

Space saving
LH-DPRE is supplied in concentrate form. Each 10 Litre bottle makes up 60 Litres of working solution thus reducing storage requirement and saving space. The Fuji FLH-P processor automatically mixes and prepares the Replenisher without the need for operator intervention eliminating errors and reducing operator time.

Ecomomical Use
Featuring from a low replenishment rate reduces running costs for the processing system.

LH-DPWE Developer

Developer for use with Brillia LH-PIE plate


LH-DPRE Replenisher

FN-6CWE Gum

LH-DPWE Developer is designed for use with Brillia LH-PIE positive thermal plate


Aqueous based developer
LH-DPWE Developer is a water based chemical with good environmental properties. This results in easier chemical disposal and cost savings.

Reduced maintenance times
LH-DPWE Developer is a very clean working developer. Less time is required to clean the developer tank within the processor during the periodical processor maintenance cycle.

Easy to use
LH-DPWE Developer comes in Ready-to-Use bottles, eliminating the need for mixing and reducing the possibility for error.

Economical usage
LH-DPWE developer has very good chemical yield properties. This results in good cost savings achieved from long developer life, stable processing conditions and low replenisher amount requirements.

LP-DRC Replenisher

Developer Replenisher for LP-NV CTP plate.


LP-NV

LP-DS Developer

FN-6CWE Gum

Replenisher designed for use with Fuji Brillia LP-NV photopolymer plates.


Aqueous based replenisher:
LP-DRC Developer Replenisher is a water based chemical with good environmental properties. This results in easier chemical disposal.

Easy to use:
LP-DRC Developer Replenisher comes in Ready-to-Use bottles, eliminating the need for mixing and reducing the possibility for error.

LP-DRZ Replenisher

Developer Replenisher for LP-NN2 and LP-NNV Newspaper CTP plates


LP-NN2

LP-NNV

FN-6CWE Gum

FN-6NWE

A universal Plate Developer Replenisher designed for use with Fuji Brillia LP-NN2 and LP-NNV Newspaper CTP Newspaper photopolymer plates.


Aqueous based replenisher
LP-DRZ Developer Replenisher is a water based chemical with good environmental properties. This results in easier chemical disposal.

Easy to use
LP-DRZ Developer Replenisher comes in Ready-to-Use bottles, eliminating the need for mixing and reducing the possibility for error.

Low replenishment
LP-DRZ replenisher is designed to minimise chemical replenishment volumes thus reducing costs, handling and environmental impact.

LP-DS Developer

Developer for Photopolymer based CTP Plates


LP-NV

LP-NNV

LP-NN2

LP-DRC Replenisher

FN-6CWE Gum

A universal Plate Developer designed for use with Fuji Brillia LP-NV and LP-NN2 & LP-NNV photopolymer plates.


Aqueous based developer
LP-DS Developer is a water based chemical with good environmental properties. This results in easier chemical disposal.

Reduced maintenance times
LP-DS Developer is a very clean working developer. Less time is required to clean the developer tank within the processor during the periodical processor maintenance cycle.

Easy to use
LP-DS Developer comes in Ready-to-Use bottles, eliminating the need for mixing and reducing the possibility for error.

LP-DZ Developer

Developer for Photopolymer based CTP Plates


LP-NN2

LP-NNV

FN-6NWE

FN-6CWE Gum

A universal Plate Developer designed for use with Fuji Brillia LP-NN2 and LP-NNV newspaper photopolymer plates.


Aqueous based developer
LP-DZ Developer is a water based chemical with good environmental properties. This results in easier chemical disposal.

Reduced maintenance times
LP-DZ developer is a very clean working developer. Less time is required to clean the developer tank within the processor during the periodical processor maintenance cycle.

Easy to use
LP-DZ Developer comes in Ready-to-Use bottles, eliminating the need for mixing and reducing the possibility for error.

Up


****

Plate Care

CS-1 Plate Cleaner

Plate cleaner for Brillia HD PRO-T processless plate


HD PRO-T2

Recommended Plate Cleaner for Brillia HD PRO-T processless plate


Plate cleaner for PRO-T:
CS-1 plate cleaner is specifically designed to compliment the Brillia HD PRO-T processless plate in a new range of plate care products designed for the press room.

MC-E Plate Cleaner

Plate cleaner for oil-based, and UV Inks. Cleaner for rollers of continuous water supply systems.


MC-E is a superior Plate Cleaner that is suitable not only for conventinal oil-based inks but also Ultra-Violet inks. MC-E can also be used as a Cleaner for rollers of continuous water supply systems.


When used as a Plate Cleaner
Can be used to effectively remove any type of plate toning or scumming. It also works very well as a scratch remover, allowing reduced press down time. - It is suitable for conventional oil-based inks and Ultra-Violet inks. - It functions very well as an ink remover on non-image areas, whilst not damaging the image area. - Suitable for use with high definition printing, such as FM screening.

When used as a Cleaner for Rollers of Continuous Water Supply Systems
After removing debris and ink on dampening rollers, apply MC-E to aid cleaning. - Will enhance the rollers hydrophilic properties improving the water supply capability to the plate. - It can be used on metal and both EPDM and NBR rubber rollers.

Plate compatibility
MC-E is suitable for Conventional plates (both positive and negative) Thermal CTP plates (LH-PIE/LH-NI) Photopolymer CTP LP-N3 plate. MC-E is NOT suitable for Photopolymer CTP plates LP-NS, LP-NN

FN-6E Gum

A Finishing gum for all CTP plates and Negative working PS-Plates


A general purpose finishing gum for all CTP plates and Negative working PS-plates supplied in concentrate form


Suitable for CTP applications
A finishing gum for use with the Brillia range of CTP plates

Waterless rinse processors
A machine finishing gum for use with Fujifilm PS-Plate processors without a water wash section

Concentrate
Supplied as a concentrate to allow flexibility

FN-6CWE Gum

Finishing Gum for all CTP plates


A general purpose finishing gum for all CTP plates and Negative working PS-plates when used in a commercial environment.


Suitable for CTP applications
A finishing gum for use with the Brillia range of CTP plates when used in a commercial print environment.

Waterless rinse processors
A machine finishing gum for use with Fujifilm PS-Plate processors without a water wash section.

FN-6NWE

A plate finishing gum designed for newspaper production.


A plate finishing gum designed for newspaper production.


Ease of use
Supplied in Ready to Use format. No mixing required.

Designed for Newspaper production
A tailored plate finishing gum formulated for newspaper plate production allowing fast drying and quick clean-up on press.

GU-7E Gum

General purpose, universal Plate Gum


A universal PS-Plate gum for use with long term plate storage applications and processors with a water wash section


Suitable for long-term plate storage
GU-7 is also suitable for long term storage of PS-plates either before or after printing.

General use gum for use in plate processors
A general purpose finishing gum for use in plate processing equipment

GU-7CWE Storage Gum

General purpose, universal Plate Gum


A universal Plate Gum for long term plate storage applications and use with processors with a water wash section


Suitable for long-term plate storage
GU-7CWE is recommended for long term storage of all plates either before or after printing

General use gum for use in plate processors
A general purpose finishing gum for use in plate processing equipment

GU-7NWE Gum

Finishing and storage Gum for newspaper application


A Ready to Use finishing and storage Gum for use in a Newspaper environment


Designed for the newspaper industry
GU-7NWE Gum is especially formulated for the newspaper industry. The formulation ensures good processing properties and quick clean-up on press.

General use gum for use in plate processors
A general purpose finishing gum for use in plate processing equipment

QC-1 Quality Checker

A liquid solution to allow plate measurement when using Brillia HD PRO-T processless plate


HD PRO-T2

QC-1 solution is a liquid when wiped over PRO-T processless plate will allow dot measurement using a plate reading densitometer


Plate measurement:
QC-1 solution, will allow plate measurement by plate densitometer when wiped over Brillia HD PRO-T processless plate

Up


****

Processor Care

Algi Stop LR

Anti-algae additive



Additive used to control the presence of algae in the wash water section of film processors

FCT-E15 Processor Cleaner

Plate processing equipment cleaner


Chemistry to enable thorough and easy cleaning of photo litho plate processors


Aqueous based solution:
FCT-E15 Plate Processor cleaner is a water based chemical with good environmental properties. This results in easier chemical disposal.

FCT-15 is a ready to use chemistry:
There is no need to mix a cocktail of chemistries, just use direct from the container.

Reduced routine maintenance time:
The use of FCT-15 reduces processor cleaning times. Built up deposits in pipe work is removed with this chemistry reducing the need to change any pipe work.

Processor Tank Cleaner

Film processor tank cleaner



Cleaner and neutralizer for the developer tank and developer rack of film processors

Up


****

Film Processing

QR-D1

Fourth generation liquid developer


A unique developer designed for use with Fujifilm Fourth Generation HQ films (also available in powder form).


"Open" developers
HQ developers can be used in conjunction with Rapid Access films as well as the HQ products.

Low replenishment rates

Lower replenishment volumes means less chemical waste and therefore lower waste management costs.

Incorporates a unique preservative and a patented anti-oxidant
The ultra stability of the HQ developers means stable calibration conditions and less chemistry changes.

Star Fix PD

Universal powder fixer for all graphic applications


A universal powder fixer for all graphic applications


Suitable for fourth generation and rapid access applications

Highly buffered

Good silver recovery characteristics

QR-D1PD

Powder developer for HQ film


Unique powder developer designed for use with Fujifilm’s fourth generation HQ film


Automatic mixing
Using the Chempact mixers the chemistry mixing is clean and easy.

"Open" developers
HQ developers can be used in conjunction with Rapid Access films as well as the Fuji HQ products.

Low replenishment, reduced packaging waste
Reduced replenishment volumes means less chemical waste facilitating lower waste management costs. With powder chemistry there are no plastic containers to dispose of.

Silver sludge suppressants, patented anti–oxidant additives and a unique preservative to maintain developer stability

This combination results in a significantly lower replenishment rate than other fourth generation systems. Additionally a very stable and clean working developer is obtained.

Flash-O-Graph Fixer

Universal liquid fixer for all graphic applications


A universal liquid fixer for all graphic applications


Good silver recovery characteristics

Highly buffered

Rapid Star

Liquid general purpose developer


Concentrated liquid high contrast general purpose rapid access developer


A liquid concentrate developer suitable for rapid access and fourth generation materials

Variable dilution to suit the application

Up


 

 

For developing machine

Film

Metal Plates

Analogue Platemaking

(PS-Plate Chemical)

CTP Platemaking

(Digital CTP)

Silver Plate

For cleaning

-

For PrintingPress

-